- Zte Gpon Snmp Management Tools
- Zte Gpon Snmp Management Software
- Zte Gpon Snmp Management Ikarus Download
- Zte Gpon Snmp Management Software
- Snmp Management Software
Configuring SNMP protocol for device management. Monitored the equipment alarms from EMS/NMS and provide technical support for Troubleshooting. Problem solving, system tuning, software upgrades, fault localization & remedy and any other integration activities. Network Management. Management Mode. Support IEEE802.3 OAM, ONU can be remotely managed by OLTSupport Remote management through SNMP and TelnetLocal management: Management Function. Status monitor, Configuration management, Alarm management, Log management. Zte Gpon Snmp Management Microsoft Word Change Units Of Measurement Download Lagu Dangdut Koplo Palapa Kebelet Amibcp Version 5.0 Kbb Turbocharger Manual Lymphatic Drainage Cardiak Flatline Drum Kit Rar File Pastor Aide Program Themes Radiant Keygen Idm. OLT C300 Completed Control,Uplink,Power Cards 2xSCXM,2xPRWG,2xGUFQ and other accessories.
ZTE GPON OLT SNMP Server Configure
Today i will discuss how to ZTE GPON OLT SNMP Server Configure in ZXA10 C220 & C300 series OLT.
Prerequisites:
- Make sure that the network device works normally.
- Log in to the ZXA10 C220 through HyperTerminal or Telnet.
Context: SNMPis essentially a request-reply protocol running over UDP
(ports 161 and 162), though TCP operation is possible. SNMP is
an asymmetric protocol, operating between a management station and an agent. The agent is the device being managed – all its software has to do is implement a few simple packet types and a generic get-or-set function on its MIB variables. The management station presents the GUI by collecting MIB data over time.
(ports 161 and 162), though TCP operation is possible. SNMP is
an asymmetric protocol, operating between a management station and an agent. The agent is the device being managed – all its software has to do is implement a few simple packet types and a generic get-or-set function on its MIB variables. The management station presents the GUI by collecting MIB data over time.
The ZXA10 C220 supports SNMP v1/v2/v3.
To configure the SNMP server, perform the following steps:
Step-1: Use the configure terminal command to enter global configuration mode.
Step-2: Use the snmp-server community command to configure SNMP community.
Step-3: Use the snmp-server location command to configure physical location information.
Step-4: Use the snmp-server enable command to configure trap type.
Note: Trap is the unsolicited information which is sent to the NMS by a managed device . It is used to report urgent events. The ZXA10 C220 supports six types of traps: SNMP, BGP, OSPF, RMON, STALARM, and VPN.
Step-5: Use the snmp-server host command to configure SNMP server (trap destination host).
Step-6: Use the show snmp config command to query SNMP configuration.
ZTE GPON OLT SNMP Server Configure Example:
Configure SNMP server:
- Community: Public
- Right: Read only
- SNMP server host: 10.62.31.123
- SNMP version: v2
ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#snmp-server community public view allview ro
ZXAN(config)#snmp-server enable trap
ZXAN(config)#snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#snmp-server community public view allview ro
ZXAN(config)#snmp-server enable trap
ZXAN(config)#snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1
ZXAN(config)#show snmp config
snmp-server location xxxx, yyy, Bangaldesh.
snmp-server contact +88-017-xxxxxxxx
snmp-server packetSize 3000
snmp-server engine-id 830900020300010289d64401
snmp-server community public view allview rw
snmp-server view allview internet included
snmp-server view DefaultView system included
snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1 udp-port 162
snmp-server enable trap SNMP
snmp-server enable trap VPN
snmp-server enable trap BGP
snmp-server enable trap OSPF
snmp-server enable trap RMON
snmp-server enable trap STALAR
snmp-server location xxxx, yyy, Bangaldesh.
snmp-server contact +88-017-xxxxxxxx
snmp-server packetSize 3000
snmp-server engine-id 830900020300010289d64401
snmp-server community public view allview rw
snmp-server view allview internet included
snmp-server view DefaultView system included
snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1 udp-port 162
snmp-server enable trap SNMP
snmp-server enable trap VPN
snmp-server enable trap BGP
snmp-server enable trap OSPF
snmp-server enable trap RMON
snmp-server enable trap STALAR
ZTE GPON OLT SNMP Server Configure
Today i will discuss how to ZTE GPON OLT SNMP Server Configure in ZXA10 C220 & C300 series OLT.
Prerequisites:
- Make sure that the network device works normally.
- Log in to the ZXA10 C220 through HyperTerminal or Telnet.
Context: SNMPis essentially a request-reply protocol running over UDP
(ports 161 and 162), though TCP operation is possible. SNMP is
an asymmetric protocol, operating between a management station and an agent. The agent is the device being managed – all its software has to do is implement a few simple packet types and a generic get-or-set function on its MIB variables. The management station presents the GUI by collecting MIB data over time.
(ports 161 and 162), though TCP operation is possible. SNMP is
an asymmetric protocol, operating between a management station and an agent. The agent is the device being managed – all its software has to do is implement a few simple packet types and a generic get-or-set function on its MIB variables. The management station presents the GUI by collecting MIB data over time.
The ZXA10 C220 supports SNMP v1/v2/v3.
To configure the SNMP server, perform the following steps:
Step-1: Use the configure terminal command to enter global configuration mode.
Zte Gpon Snmp Management Tools
Step-2: Use the snmp-server community command to configure SNMP community.
Zte Gpon Snmp Management Software
Step-3: Use the snmp-server location command to configure physical location information.
Zte Gpon Snmp Management Ikarus Download
Step-4: Use the snmp-server enable command to configure trap type.
Note: Trap is the unsolicited information which is sent to the NMS by a managed device . It is used to report urgent events. The ZXA10 C220 supports six types of traps: SNMP, BGP, OSPF, RMON, STALARM, and VPN.
Step-5: Use the snmp-server host command to configure SNMP server (trap destination host).
Step-6: Use the show snmp config command to query SNMP configuration.
Zte Gpon Snmp Management Software
ZTE GPON OLT SNMP Server Configure Example:
Snmp Management Software
Configure SNMP server:
- Community: Public
- Right: Read only
- SNMP server host: 10.62.31.123
- SNMP version: v2
ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#snmp-server community public view allview ro
ZXAN(config)#snmp-server enable trap
ZXAN(config)#snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#snmp-server community public view allview ro
ZXAN(config)#snmp-server enable trap
ZXAN(config)#snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1
ZXAN(config)#show snmp config
snmp-server location xxxx, yyy, Bangaldesh.
snmp-server contact +88-017-xxxxxxxx
snmp-server packetSize 3000
snmp-server engine-id 830900020300010289d64401
snmp-server community public view allview rw
snmp-server view allview internet included
snmp-server view DefaultView system included
snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1 udp-port 162
snmp-server enable trap SNMP
snmp-server enable trap VPN
snmp-server enable trap BGP
snmp-server enable trap OSPF
snmp-server enable trap RMON
snmp-server enable trap STALAR
snmp-server location xxxx, yyy, Bangaldesh.
snmp-server contact +88-017-xxxxxxxx
snmp-server packetSize 3000
snmp-server engine-id 830900020300010289d64401
snmp-server community public view allview rw
snmp-server view allview internet included
snmp-server view DefaultView system included
snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1 udp-port 162
snmp-server enable trap SNMP
snmp-server enable trap VPN
snmp-server enable trap BGP
snmp-server enable trap OSPF
snmp-server enable trap RMON
snmp-server enable trap STALAR